In the process of decoration, many decoration whites are very vague on some decoration orders, I don't know which step to do first. First install the floor, or first install the wardrobe? First install the cabinet, or install the hood first... About 90% of the decoration white can not figure out the order. Many people have suffered a lot because they are not prepared, which leads to regrets during the renovation.
Floor VS wardrobe: the key to see what wardrobe you bought
In order to better protect against moisture, many owners will choose to lay the floor and then install the wardrobe. Moreover, after the floor is installed, the floor is relatively flat, which is also conducive to the wardrobe. Many people may enter a misunderstanding, so they must first install the floor and then build the wardrobe. Master Wang, who has more than 20 years of experience in woodworking, told reporters that the order in which the floor and the wardrobe are installed depends on what kind of wardrobe you choose.
If you choose a finished wardrobe, you must first install the floor. If you choose a custom closet, you need to measure it before the floor is leveled and after the floor is leveled. After the floor is finished, assemble the custom closet. If you are looking for a carpentry to make a wardrobe, you can first make a wardrobe and then lay the floor, which can save some floor materials. The disadvantage is that the wardrobe can't move.
The insiders reminded that for custom closets and finished wardrobes, if you want to install the wardrobe first under special circumstances, you must pay attention to the ground level needs to be leveled in advance.
Range VS cabinet:
It is best to install a range hood first.
When Mr. Liu's home was renovated, he chose the whole cabinet. Like other renovation processes, before the hydropower transformation, the cabinet workers measured the size and reserved the position of the range hood. After the tiles were put on, the cabinet manufacturers sent people to measure them again. There are no problems with the cabinet installation. However, when buying a hood, I found that the cabinet was reserved.
The kitchen decoration follows the principle of first going up and down, first in the future, first in the outside, and then in the first place. It is best to install the range hood first. After installing it, wrap it in a thick plastic bag to prevent it from falling, and then install the upper row of cabinets.
The insiders said that it is OK to install the cabinet first, but the bottom panel of the cabinet above the hood should be larger than the top surface of the hood. When installing, first remove the bottom panel of the upper cabinet, and then install the hood after installing the hood. The bottom plate is installed.
Gate stone VS door:
The order must not be wrong
"The door is not very smooth, and it has not been installed for a day." Ms. Wu first installed the threshold stone, but when the door master went to the door, she said that the door stone was first, but the master who installed the stone said it was always the first. Install the door and install the door. In the decoration, the bricklayer is usually attached to the stone. Only when the threshold stone is ordered and completed, can the size of the door be as accurate as possible and the size of the door can be better measured.
Mr. Hu, the project manager, said that the order in general is to measure the door—installing the threshold stone—ground leveling—installing the door—to install the wooden floor. After the door sill is installed, the vertical plate of the door stands directly on the stone, so that the stone can isolate the door and the wet ground. If the door is installed first, the closing of the stone and the door panel interface is not easy to handle.
Globe Valve is one of the most widely used valves, it is durable, easy to fabricate and maintance. Ningbo RMI Plastic Co.,Ltd offer PVC Globe Valve , CPVC globe valve, PVDF Globe Valve, PP Globe Valve , PPH Globe Valve , PTFE lined globe valve, with flange end and screw connection, design and fabricate as per standard DIN, ANS, JIS. Plastic Globe Valve is suitable for corrossive medium application, widely used in Chemical factory.
Foot Valve also named bottom valve, the function of the valve is to prevent medium backflow, mainly used to protect pumps and other equipments. RMI PLAST offer different models of plastic foot valve with materials of PVC, CPVC, PVDF, PP, PPH, PTFE lined, with flange end and socket connection as per ANSI, JIS, DIN standards.
Sampling Valve is used to obtain medium sample from pipeline or equipment, RMI PLAST brand PVC Sampling Valve is special designed with small size, light weight, easy handle. 1/4" size male thread end and 1/2" size coupling end is easy to install and replace.
Safety Valve Foot Valve Globe Valve and Other Valves
Globe Valve,Foot Valve,Sampling Valve,PVC Globe Valve
Ningbo RMI Plastic Co., Ltd. , https://www.rmiplast.com