| Home>Bearing knowledge>Bearing grinding |
Bearing grinding
Source: Bearing network time: 2013-10-22
| /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089'; |
The appearance of the interspersed spiral traces exhibits such traces. The reason is mainly because the flatness of the grinding wheel is poor; there is a concave-convex appearance; during grinding; the grinding wheel and the workpiece are only slightly touched; when the workpiece or the grinding wheel reciprocates several times; The workpiece embodiment will reproduce the interpenetrating spiral and can be observed by the naked eye. The pitch of these spirals is related to the workpiece table speed and the workpiece rotation speed; together with the grinding wheel axis and the worktable rail are not parallel.
ㄒ唬┞èªå’ å‚» å‚» å‚» 饕 1. The grinding wheel is poorly trimmed; the corners are not chamfered; the coolant is not trimmed,
2. The workbench guide guides too much lubricating oil; causing the workbench to float.
3. The machine tool accuracy is not good,
4. Grinding pressure is too large.
Ǘ┞èªå’ å‚» å‚» å‚» å‚» 1 1. The V-shaped guide rail is not well rigid; when grinding, the grinding wheel is offset; only the edge of the grinding wheel and the touch of the work surface,
2. When the quarrel is repaired, the commutation speed of the workbench is unstable; the precision is not high; the trimming of the grinding wheel is slightly less,
3. The workpiece itself is poorly rigid,
4. The sand on the grinding wheel is broken and the iron scraps under the grinding of the workpiece are attached to the outer surface of the grinding wheel; for this purpose, the finished grinding wheel should be washed or rinsed with cooling water.
5. The dressing of the grinding wheel is not good; there are some bumps.
The main reason for the appearance of the scale-like appearance of fish scales is that the cutting edge of the grinding wheel is not sharp; the phenomenon of "squatting" occurs during grinding;
The detailed reasons for the appearance of fish scales on the surface of the workpiece are:
1. There are waste and oil on the surface of the grinding wheel.
2. The wheel is not trimmed,
3. The grinding wheel becomes dull. The trimming is not sharp,
4. The diamond fastening frame is not strong; the diamond rocking or the quality of the diamond is not good,
5. The hardness of the grinding wheel is not uniform.
The main reason for the reappearance of the fluffing marks on the surface of the working surface is that the coarse-grained abrasive grains fall behind; the abrasive grains are formed between the workpiece and the grinding wheel.
The detailed reason for the appearance of the workpiece when it is being ground during grinding is:
1. Traces left over from rough grinding; not worn out during fine grinding,
2. The coarse abrasive grains and fine abrasive grains in the coolant are not cleaned.
3. When the coarse-grained grinding wheel is just finished, the abrasive particles are simply dropped.
4. Useful period of data tolerance or grinding wheel is too soft,
5. Inadequate cooperation between abrasive resistance and workpiece data tolerance.
The surface of the workpiece has a straight wave trace. We cut the cross-section of the ground axis of the milled workpiece and enlarge it. It can be seen that its periphery is similar to a sine wave. It has no transitional translation along the axis of the axis; the orbit around the sine wave is The corrugated cylinder surface; also known as the polygonal shape. The reason for the straight waveform is the movement of the grinding wheel relative to the workpiece or the periodic change of the pressure of the grinding wheel on the workpiece to cause oscillation. This oscillation may be forced to oscillate; It may be self-oscillation; therefore, the direct wave frequency on the workpiece is often more than one.
The detailed cause of a straight waveform trace is:
1. The gap of the grinding wheel spindle is too large.
2. The hardness of the grinding wheel is too high,
3. The static balance of the grinding wheel is not good or the grinding wheel becomes dull.
4. The workpiece speed is too high,
5. The lateral feed is too large,
6. The grinding wheel spindle bearing wears; the cooperation gap is too large; the radial runout occurs,
7. Grinding wheel compaction arrangement or workbench "åŒåŒ" and so on.
The surface of the workpiece reproduces the burn marks. The appearance of the workpiece tends to burn during the grinding process; there are several types of burns; one is the direction of the burn along the grinding wheel; it is dark black plaque, and the second is a line or intermittent line.
The appearance of the workpiece is burned during the grinding process; there are several reasons for the following:
1. The grinding wheel is too hard or the grain size is too fine to be too dense.
2. The feed rate is too large; the supply of cutting fluid is lacking; the heat dissipation condition is poor,
3. The workpiece speed is too low; the grinding wheel speed is too fast,
4. The wheel is too oscillated; it burns due to the constant change of the grinding depth.
5. The dressing of the grinding wheel is not timely or the repair is not good.
6. Diamond is sharp; the wheel is not well trimmed,
7. When the workpiece is coarsely ground, the burn is too deep; the amount of fine grinding is too much. The workpiece clamping force or suction is lacking; under the effect of grinding force; the workpiece has a stalling appearance.
Then how does the appearance of the workpiece know how to burn in the grinding process? This should be checked out after a regular pickling.
After the workpiece is pickled; when the surface is wet; it should be visually inspected immediately under the astigmatism lamp; the normal appearance is evenly dark gray. If it is a software point; it will appear cloud-like dark black mottle; and the perimeter is not fixed, if it is decarbonized; Gray or dark black spots, if the grinding cracks; the crack is cracked; if it is a burn; the first is a dark black plaque along the direction of the grinding wheel; the second is a line or intermittent lines. The above-mentioned burn appearance is presented; it is necessary to analyze the cause in time; adopt a useful method to solve it;
Appearance roughness does not meet the requirements of the bearing surface roughness of the specification and process requirements; but in the grinding process and super-precision process; due to various reasons; often can not meet the requirements of the rules.
The primary reason for the roughness of the workpiece to meet the requirements is:
1. The grinding speed is too low; the feed rate is too fast; the feed rate is too large; the no feed grinding time is too short,
2. The workpiece speed is too high or the workpiece axis and the grinding wheel shaft are too large.
3. The grinding wheel is too thick or too soft.
4. The dressing speed of the grinding wheel is too fast or the trimming arrangement is too large.
5. The diamond of the dressing wheel is not sharp or of poor quality.
6. The quality of ultra-precision oilstone is not good; the orientation of the device is incorrect.
7. The quality of ultra-fine kerosene is not up to demand.
8. Super fine time is too short.
The bearing is in the grinding process; its working appearance is ground by a high-speed rotating grinding wheel; therefore, if it is not operated and adjusted according to the operation instructions during grinding; it will present various shortcomings in the bearing operation; The overall quality of the bearing.
Recommend to friends comments close window
| Bearing related knowledge |
| The effect of smooth grease on the life of KOYO bearing is discussed in detail. The timing of the bearing is smooth and smooth. The single-stage single-suction centrifugal pump bearing smoothing method is modified. How to push (positioning) bearing device imported bearing sealing equipment |
This article links to http://
Please indicate China Bearing Network http://
Previous: Powder metallurgy oil bearing next edition: annealing heat treatment (2)
Indoor lighting
LEDER offers a range of modern indoor illumination, including LED down light , Track Light ,Linear Light,Indoor Wall Light,LED Panel Light,strip light,LED tube and bulbs as so on. Our indoor lights and indoor LED lighting solutions are ideal to create an atmosphere that is expected of LED lighting in commercial or residential Settings.
We believe in the aesthetics of indoor design and the role of lighting in enhancing the atmosphere of the indoor space, whether for entertainment or work. The indoor of the home is a place of relaxation, warmth and intimacy, while at work it is a place of creativity, efficiency and collaboration. The basic idea is that indoor space is an area where one can resonate with individuals or professionals and perform at their best. This is the importance of indoor lighting and the role of lamps and lanterns, they are used to enhance the space, bring the best results for the people who use the space. Modern Spaces may be limited by light, and sometimes the use of light in indoor Spaces during the day is almost inevitable. LEDER indoor lighting is by using the method of people-centered, applicability in lighting design and play out the best effect, make the person can achieve the best results in indoor space.
Grow Lamp ,Indoor Grow Lighting ,E27 Indoor Wall Light,Indoor Motion Sensor Light
JIANGMEN LEDERLIGHT LIGHTING Co.,LTD , http://www.walllightoutdoor.com