PVC to linseed oil
Linseed oil
Composition: oxidized linseed oil, a mixture of cork and wood flour, laminated to the jute backing, and added to other non-natural chemicals.
Scratch resistant
The linseed oil is hard and soft. This is why thick linseed oil is less resistant to scoring.
Dimensional stability
The dimensional stability of linseed oil is very poor. Therefore, a strong glue must be used.
Linseed oil is not as stable as PVC.
Linseed oil needs to be cured under natural light.
The result: the sample and the actual product will differ. Yellowing. Linseed oil is very resistant to maintenance products (pH > 7). Linseed oil needs to be repolished and waxed. Special products must be used. In all cases, no The added PVC floor is superior to linseed oil. Linseed oil is much harder than PVC products. However, this feature becomes inconvenient in the long run, because linseed oil is unstable and exaggerated to reflect imperfect ground. Because the surface is porous, all stains must be quickly removed, otherwise the surface will leave a mark that is difficult to remove. It has to be re-polished and waxed. The original linseed oil has good abrasion resistance. But it must be polished and waxed otherwise it will become dirty. Because it is not a thermoplastic material, it cannot be recycled. The burnt marks can be easily Grinding off. But... For grinding deep marks, the transparent PVC floor is much easier than linseed oil. It is very difficult to install linseed oil, the linseed oil will break if the room temperature is too low. Because: its absorption nature It is dimensionally unstable, so the product must be quickly installed with super glue. During the drying of the linseed oil, it is dried by a crossbar in a 15 m long drying oven. The light bars left by these crossbars Imprinting is impossible to remove in later processes. One day, an installation team can lay 80 to 100 m 2 of PVC or 60 m 2 of linseed oil. The linseed oil is not sensitive to temperature. It is not possible to weld with the same material, so it is not a weld but a “seamâ€. "Seam", so linseed oil can not be divided into E3 waterproof. Linseed oil is not suitable for use in wet rooms or areas with clean requirements. Because the production method is limited in decoration. Linseed oil emits a strong smell and stays in the installation. In the room.
PVC to rubber
Rubber defect
The product range is narrow, compared with PVC. Strong smell. Poor sound insulation. Maintenance is difficult. Metallization is difficult to adhere to the surface. Rubber will fall off. If the rubber is not metallized, it will become soft and sensitive to friction. The rubber is easy to slip. Installation is difficult: too heavy to cause installation is laborious. Bubbles will appear if the installation method is not correct (because rubber is not a reinforcement material). Requires a perfect self-leveling base layer or rubber will exaggerate the defects of the base layer. Rather than welding. Poor anti-friction (according to Taber abrasion test). A large amount of energy is consumed in production (the heat required for vulcanization, the energy required to stabilize the product).
PVC to textile
Textile defects
Textiles will change color. Removing the carpet will affect the overall effect of the room. Hygiene issues (sensitivity, &hellip. difficult to maintain.
PVC to tile
Tile defects
PVC: Low price and installation cost, it is very important for collective housing (budget is tight). Installation is more difficult than PVC. It is difficult to remove the tiles after installation, especially in the kitchen and bathroom of the collective apartment.
PVC to resin
Resin defect
Too thin (2mm thick), thin = risk of cracking. On-site production, the main disadvantages are: irregularities, mixing problems, unfavorable site conditions, ... These will have a negative impact on the quality of the ground. There are many unsuccessful projects given to the resin A bad image. The surface layer of the resin is only 0.15 mm thick, so it is easy to remove. At the same time, too much material is added to make the ground easy to lighten after rubbing. Installation problem: The base layer must be perfect (no grease, no dust, clean and smooth) and no moisture or the ground will crack quickly. Other installation problems: Once Errors cannot be modified. Maintenance is difficult (after printing, leaving marks or loop marks on plain materials). Decorative is not as good as PVC: limited color (mainly monochrome) and three-color mixture (many additions). Now the market is mainly Monochrome. However, the final effect is often disappointing due to the scattering of particles on the ground.
PVC on wooden floor and rolled floor
Rolling ground defects
Limited to U3 level. Seam problem in hospital (E1): Not suitable for wet environment. Thin wear layer: 0.15 mm thick in U3 category (product composition: wear layer 0.15 mm thick + printed layer + fiber strip). Low resistance to scratching. Defects in the margin of the floor strip: The wear on the margin of the floor strip deteriorates the appearance of the floor. Walk echo: Increases noise (echo). Uncomfortable walking.
Wood floor defects
Wood flooring is not a true competitor for PVC because wooden flooring cannot be laid in wet rooms. It is a noble product (luxury industrial and commercial floor), high price and expensive maintenance costs (polishing and varnish). “Fake wood flooring†consists of a high-grade real wood surface and resistant wood. The disadvantage is that the varnish can only be brushed once because the surface layer cannot withstand multiple sandings. .
Ultra Plantâ„¢ Grow Light offers One Chip Technology aimed to meet your indoor growing expectation such as improve plants' quality, increase yield, or better the margin, etc., all for helping you realize a higher return on your crops.
Ultra Plantâ„¢ Grow Light is combined our advanced All-In-One technology with patented optical design and customized light full spectrum supported from our experienced LED engineers, plant specialists and other partners working on horticulture.
From Ultra Plantâ„¢ APP, you are able to schedule the growing process including photoperiod, brightness and spectral in advance. The lighting system will help you grow smarter, easier and better.
Ultra Plantâ„¢ is the most versatile horticultural grow lighting fixture for indoor plants with flexible full spectrum, brightness control and uniform, wider light distribution, suitable for top lighting of all types of crops. No matter it applies to anywhere for any crop, Ultra Plantâ„¢ can do perfect work for you.
Grow Light On Seedling,Seedling Grow Lights,Seedling Led Grow Lights,Best Grow Light On Seedling
Feton Corporation , https://www.ultraplantled.com