Winter tile is easy to fall off
Tiles and tiles must be treated with water before paving, and must be saturated with moisture. Only in this way, it is not possible to bond with cement because of the suction water.
Solution: Winter tiles and tiles must be soaked in water prior to pavement. Make sure the water is saturated. Only in this way, the phenomenon of hollowing and falling off will not occur due to the weak adhesion between cement and cement due to the suction water. In addition, no matter whether it is a wall tile or a floor tile, it must be transferred from the outdoor to the interior for 24 hours. Only when it is adapted to the indoor temperature can it be paved, so as to avoid emptying or falling off after construction.
Leave expansion joints when installing
In the winter decoration, the seams of the doors and windows should not be too small, so as to avoid tight heat and tightness in the summer. When paving solid wood flooring, about 2mm of expansion joints should be left around.
Solution: During the winter decoration, the seams of the doors and windows should not be too small, so as to avoid tight heat and tightness in the summer. When paving solid wood flooring, about 2mm of expansion joints should be left around. When furniture is made, about 0.1mm of interface seams must be left. The floor and wall joints should be bridged with floor layers and can be well handled. The disadvantages of excessive wall and floor gaps.
Bad winter paint brush effect
In case of severe winds and cooling of the weather, it is not advisable to carry out oil work. Because the wind and sand in winter are relatively large, dust and paint are liable to be attached when the paint and paint are dry. Care should be taken to select a windless weather for painting.
Solution: In the event of strong winds and cool weather, it is not appropriate to carry out oil work. Because large wind and sand in winter, paint and paint are not dry, it is easy to attach dust, should pay attention to choose the weather without wind to brush, ensure the temperature of the coating application of the environment Not less than 5 degrees Celsius, the ambient temperature when the varnish is applied is not less than 8 degrees Celsius, and should be applied strictly according to the temperature in the product description. To prevent sand from falling on the paint surface, close the doors and windows.
Plaster line moisture content to be controlled
When the gypsum board ceiling operation is performed, the moisture content of the wood keel must be controlled below 12%, and the keel must be firm and loose.
Solution: When the gypsum board is suspended, the moisture content of the wood keel must be controlled below 12%, and the keel must be firm and loose. This will prevent cracks in the gypsum board ceiling. Between the gypsum board and the joint between the gypsum board and the wall, leave a gap of about 0.5 cm. Use gypsum powder and latex to reconcile the joints. Then double stick the kraft paper and scrape the putty to prevent the plaster line. Cracking.
Winter construction prevents wall cracking
Putty does not dry on the brush coating, the wall is easy to "sweat" or even a large area of ​​cracking, often open window ventilation, the time is best to choose between 10 am to 4 pm.
Solution: Putty does not dry on the paint, the wall is easy to "sweat" or even a large area of ​​cracking, often window ventilation, the time is best selected between 10:00 to 4:00. The relatively high temperature during this period of time can prevent new batches of putty from freezing. After the putty was completely dry the first time, it was re-approved for the second time. After the second putty is completely dry, sand it carefully.
Veneer cracking
All the decorative panels should be laid flat, with a large core board on the bottom and a large core board on the top, which cannot stand upright. This will prevent the panel from cracking and warping.
Solution: After the panel has been transported to the construction site, apply a dry towel to wipe off the dust and apply the brush twice to the back. All the decorative panels should be laid flat, with a large core board on the bottom and a large core board on the top, which cannot stand upright. This will prevent the panel from cracking and warping.
Winter wood is easily deformed
The main material used in the decoration, especially the wood, needs to be placed in a room with heating equipment for three to five days in order to evaporate the moisture that is produced due to temperature changes.
Solution: The main materials used in the decoration, especially the wood, need to be placed in a room with heating equipment for three to five days to evaporate the moisture that is produced due to temperature changes. This is done so that the moisture content of the wood is close to the level in the house, so that wooden deformation after the decoration can be avoided.
Cracked ceiling
The moisture content of the keel must be controlled below 12%. For cracks that occur due to different material cold shrinkage factors, the construction personnel should take measures to reserve joints.
Ceilings with wooden keel structure may crack
Cause: Wind, dryness, and cold are the causes of the cracking of the wooden keel ceiling.
Measures: The moisture content of the wood keel must be controlled below 12%. For cracks that occur due to different material shrinkage coefficients, the construction staff should take precautions to prevent joints. All wood joints are controlled at 1 mm. The joints of gypsum board and cement board are controlled at 8mm. Therefore, when constructing, ceilings with wood keel structure should be avoided as much as possible, and light steel keel ceilings are preferred.
Living room ceiling aisle ceiling paint window coating interior decoration cement floor tile ceramic tile floor tile
Our Mother of Pearl Bathroom Set includes Mother of Pearl Soap Dish, mother of pearl soap dispenser, Mother of Pearl Tissue Box, mother of pearl amenity tray, mother of pearl Amenity box , Mother of Pearl Dustbin , mother of pearl cotton holder, mother of pearl Toothbrush Holder etc. All of our products are made from natural mother of pearl materials, such as Tahiti black mother of pearl, white mother of pearl, golden mother of pearl, New Zealand paua shell, Chinese river shell, Chinese Freshwater shell etc.
With professionanl artisans, all of our mother of pearl bathroom sets are handcrafted made. Also, customized design and Logo are acceptable.
Feature of Mother of Pearl
1), Exquisite pearl texture
MOP is the mother of pearl cultured all kinds of pearls, and the colors are natural and lustrous, elegant and charming.
2), Breath of the Oceans
Because of sea differing climate of the would's sea area, it cultivates natural and colorful mother of pearl. With special textures and shades, the colors of MOP are pearl white, golden, champagne, pink and mysterious black,etc.
3), Green and Natural
Mother of pearl cultures the pearl; It's very strict to the environment of growth waters, so the worldwide pearl farms select the fine-quality waters for breeding.
4), Enviromental protection and health
The vast majority of pearls are cultured. Also we have passed SGS certification, which shows our products are completely harmless to human health. It complys with the modern design concept of enviroment protection and returning to its original nature.
Mother of pearl Bathroom Sets
Different colors and mother of pearl bathroom sets are as follows:
1) Chinese river shell bathroom set
2) Chinese freshwater mother of pearl bathroom set
3) Golden mother of pearl bathroom set
4) Black mother of pearl bathroom set
5) New Zealand paua shell bathroom set
Mother of Pearl Bathroom Set
Luxurious MOP Bathroom Accessory Set,Mother of Pearl Bathroom Set,Shell Mosaic Bathroom Set,Resin with Shell Bathroom Accessory Set, Sea Shell Bathroom Set
Jiangxi Zhaojun Industrial Co.,Ltd , http://www.zhaojunshell.com