Vacuum booster pump is mainly used for drawing light vacuum booster brake system can also be used for other transport vehicles and construction machinery. The use of vacuum assisted braking system can improve brake reliability and reduce driver fatigue, help reduce the incidence of traffic accidents and improve vehicle safety. At present, the rapid development of domestic light vehicles, which undoubtedly for the vacuum booster pump provides a vast market. Therefore, in the promotion and use of the process, we must understand and master its performance, principles. The only way to effectively ensure the pump braking performance, extend the service life, play a safety role. 1. Vacuum booster pump works Vacuum booster pump mainly by the pump body, rotor, slider, pump cover, gear, seals and other components, when the pump work, with four slide eccentric rotor counterclockwise Rotating, the slider in its own centrifugal force, close to the inner wall of the pump glide, suction studio continues to expand, was pumping gas through the suction tube to open the one-way valve (pump built-in check valve, the system plays the role of packing Into the suction studio. When the slider to a certain position, the inhalation is completed, then inhaled gas is isolated, the rotor continues to rotate, the isolated gas is gradually compressed - the pressure rise. When the studio goes to communicate with the vent, the gas is vented from the vent. Pump work process, the slider will always be divided into four pump chamber, the rotor per revolution, there are four suction and exhaust process. 2. Usage and maintenance precautions Vacuum booster pump is a high precision and sensitive working pump. The following rules must be strictly observed when using it: (l) The vacuum booster pump lubricates the friction surface with oil to seal the gaps (rotor, Slider, pump body, cover the gap formed), it must choose the right lubricant and the appropriate lubrication. (2) should be used regularly check the operation and lubrication is normal, with or without abnormal noise, so that timely detection and troubleshooting. (3) should always check the use of the pump leaks. (4) If you do not use the vacuum booster pump for a long time, do not immediately work full load when reused. 3. Common failures and troubleshooting (1) the maximum pump vacuum is low, the pump extraction time is extended; failure causes: Run, lubricating fluid is not sufficient; suction pipe leaks; parts wear; gap increased leakage. Troubleshooting: Check the viscosity of lubricating oil, if not qualified, the replacement of the appropriate viscosity of the oil; Check whether the pipeline leaks, if the leak, you need to replace the leak; Check the parts for wear and tear, if worn Those who need grinding or replacement of new parts; check the pressure of lubricating oil, and meet the requirements. (2) pump does not hold pressure, leakage; failure causes: seal leakage diagnosis and troubleshooting: Check the seal is worn and inelastic, if worn, need to be replaced with a new seal. (3) leaks at each interface; cause of the malfunction: the connector is loose or the seal is damaged. Fault diagnosis and troubleshooting: Check whether the loose joints, if loose, need to be sealed sealant fastening joints; if the seal is damaged, the need to replace the new pieces. 4. Disassembly pump precautions Each component in the vacuum booster pump has high machining accuracy and assembly accuracy, in general, users do not disassemble, there are questions should be sent to the manufacturer or repair center for inspection and repair, if Must be disassembled, then pay attention to the following: (l) vacuum booster pump rotor and gear are interference fit, can not be removed. (2) The parts are not allowed bump and scratches, the parts clean with kerosene, stored in a clean box. (3) should pay attention to the sliding block slider arc outward, may not be installed. (4) parts must be clean assembly. (5) After the pump is assembled, the rotor should rotate flexible. 5. Storage Vacuum booster pump should be stored in a dry, non-corrosive gas warehouse, not in the high temperature and -20 ℃ below the long-term storage in low temperature environment, in order to avoid aging rubber seals, and often check the corrosion conditions, if necessary Replace pump anti-corrosion oil.
Aluminium Alloy Swing Door Handle
Aluminium Alloy Swing Door Handle,Electronic Screen Panel Sliding Door Handle,Stainless Steel Door Handle,Zinc Key Hidden Wooden Door Handle
BOGO HARDWARE & FITTING CO.,LTD , https://www.bogo-hardware.com