After laying the floor, you may not see any problems if you do not look closely, but the problems such as color difference, drumming, deformation, high and low deviation, and walking noises when walking, and blinking, cracks, scratches, etc., are not timely if they are not accepted. It was found that it would be difficult to think about changes after staying. Therefore, the acceptance of wood floors is very important.
Wood floor pavement acceptance considerations
1, check the color of the floor.
If the color difference is too large, directly affect the appearance, you can ask for exchange; if the color is too consistent, almost no color, it depends on the floor surface pattern is the same. If the pattern is almost the same, it may be craft wood floor, not the material floor of the so-called precious wood species. Now some flooring material suppliers use ordinary wood flooring materials, but in the surface paste a layer of valuable wood veneer to shoddy, said to be moisture-proof, in fact, is afraid of being seen opposite the pattern and the front of the inconsistencies .
2, check the floor surface
Visually inspect the surface of the wooden floor for planing, grinding, no scars, russia and burrs, with clear patterns, uniform color on the surface of the clean oil, proper paving direction, tight seams on the surface layer, staggered joint locations, and clean surfaces. The quality of the wooden floor surface joints shall comply with the following requirements: tight joints, staggered joints, clean surfaces, tight joints, firm nails, no adhesive glue, reasonable arrangement of plate sections, and uniform peripheral edge width.
After laying the first row of solid wood flooring, the installer should pull straight and measure the level. If it needs to be adjusted immediately, it will affect the installation of the solid wood floor. After laying, it is better to take the ruler upright on the solid wood floor and see There is no lifting. For flatness, check by using a ruler to see if there is a tilt, and adjust the deviation of the flatness within the allowable range.
4. See if the floor sounds
The unevenness of the ground caused some floors and wooden keels to hang, and the floor was easy to make noises. If the wood keel is not firm, it is easy to produce the same situation, so be sure to check the wood keel after it is finished. You can step on the wooden keel with your feet and check if the wooden keel is firm by shaking your feet. In particular, more attention should be paid to the acceptance of the wall parts and door openings, and where there are sound parts, we must walk around to determine the specific location of the sound and make good marks. In this case, you can ask to remove the resurfacing. The site where there are sounds is caused by non-standard operations and unqualified materials used by construction workers during the construction process. The operation is not standardized, mainly reflected in the fixed keel is not solid; material failure is mainly reflected in the ground keel without drying. Some renovation construction units use undried keel construction. The surface shows signs of drying. In fact, they did not dry. The keel with high moisture content will shrink in volume during the natural drying of the wood, causing looseness.
5, acceptance of the floor deformation, warping
Acceptance method is to use a 2 meter long ruler, leaning on the floor, the flatness should not exceed 3 mm. More than a few measurements, if the passing rate of 80% or more is considered qualified, and vice versa, is unqualified. Sometimes we find that the floor is partially arched: if it is a solid wood floor, it is because it is too tight or the floor is too dry (water content is too low); if it is a laminate floor, it is a poor quality floor. Therefore, the arching of the floor is a serious quality problem.
6, the acceptance of the baseboard
The skirting boards have tight joints, smooth surfaces, and a uniform height and wall thickness. Checked with a 2-meter ruler, the ground flatness error is less than 1 mm, the gap width is less than 0.3 mm, the mouth plate straightness error is less than 3 mm, and the seam straightness error is less than 2 mm. The location of the interface of the corner line is too large at this position, and it has not been repaired with glue. This is very unpleasant in the later period, and the seams are easy to hide dust.
7. Acceptance of buckles
The door clasp should be installed directly under the door. It is advisable not to leave the inside and outside of the door after closing the door. The gap between the clasp and the door is between 3 mm and 7 mm, and the door can be opened and closed freely. The buckle should be installed firmly and stably. You can kick the middle part of the buckle to check if the sides of the buckle are tilted or loose and there is no abnormal sound.
Commonly due to the untreated keel, there are locusts inside. When it was found that there was a blink, the floor was already almost cracked; gaps and scratches were known at a glance.
Things that owners need to pay attention to in this step
1. The paving of the floor is the last step in the home renovation. Normally, after finishing the floor, you can move into the furniture to move. There is also the need to say how many gaps to keep behind the door before customizing the door.
2. The laying construction party shall issue a floor warranty card (single) and promise to be obligated during the floor warranty period.
3. In the area where the floor is laid, the furniture with large volume and weight should not be placed symmetrically, so as not to affect the free expansion and contraction of the floor.
Flooring Flooring Flooring Flooring Flooring
Laminated Glass is produced when two or more glass lites are permanently bonded with one or more plastic interlayers (PVB) using heat and pressure. The glass and interlayers can be a variety of colors and thicknesses. Laminated glass is often called [safety glass" because it meets the requirements of various code organizations. Laminated glass can be broken, but the fragments tend to adhere to the plastic layer and remain largely intact, reducing the risk of injury. Laminated glass can be incorporated with heat-strengthened and Tempered Glass to further increase impact resistance. Clear laminaterd glass is widely used for windows, doors, glass walls, partitions, room divider, balcony, balustrade, fence and so on. And also Colored Laminated Glass, ultra clear laminated glass, printed laminated glass can also be choices for different applications.
It can be made into clear laminated glass, colored laminated glass, Triple Laminated Glass, laminated Insulated Glass , printed laminated glass, Low-E Laminated Glass, toughened laminated glass, tempered laminated glass and so on.
Frosted Laminated Glass,Laminated Safety Glass,Cutting Laminated Glass, SGP Laminated Glass
Shanghai Lead Glass Co.,Ltd , https://www.leadglazing.com