The washing machine faucet is a very important part of the washing machine. There are many detours on the washing machine faucet, especially the fully automatic washing machine. However, the automatic faucet faucet leakage phenomenon, many people may have encountered, then, encountered automatic washing machine faucet leak how to do it? How to solve it? Let's take a look with Xiaobian.
Automatic washing machine faucet leak how to do and solutions
There are many reasons for leaking faucets. Once a leak is discovered, you should check which part is faulty and replace the accessory.
The most common is the damage to the water stop tape on the tap part (fixing screw). In this case, simply use a wrench to remove the faucet, and re-roll the new sealing tape in place of the screw.
If the tap is tightened, the reason for the leakage may be water leakage at the outlet, which is usually caused by the worn shaft washer in the faucet. In this case, you can use a pair of pliers to loosen and remove the cover, remove the shaft washer with a clamp, and replace it with a new one.
In addition, leakage of the gap in the lower part of the faucet can be caused by the wear of the triangular gasket in the gland. In this case, you can loosen the screw to remove the boring head, then remove the pressure cap loosely, then take out the triangle seal inside the gland and replace with a new one.
In addition, the loose cap nut may also cause water leakage at the joint, and the cap nut can be re-tightened or replaced with a new U-shaped gasket.
Q: Why did I replace the entire faucet or leak it?
Answer: Some leakage problems are not related to the faucet itself. It may be due to improper installation of the upper water hose and faucet body. In addition, it may be due to problems such as aging, unstable water pressure, or corrosion of the water supply hose to the faucet. Once the Sheung Shui hose cracks, bursts and other issues, the consequences will be very serious. Therefore, experts recommend checking or replacing the water hose every 1-2 years.
The most important thing for a faucet leaking in a washing machine is to find out why it leaks.
With regard to the repair of leaks at faucet joints, the cause of water leakage is nothing more than the damage of the sealing tape of the tap part (fixed thread). Therefore, as long as you use a wrench to remove the tap, re-roll the new sealing tape in place of the fixing screw. Here are the maintenance steps:
1. First, tighten the water tap first and use a wrench to turn the tap counterclockwise.
2, the threaded hole outward, in the threaded part with wind-printing tape clockwise roll 5-6 back.
3, to see if the faucet is adjusted well with water, board clamp clockwise direction into.
4, after the installation is complete, open the main switch to try and confirm to see if there will be leakage.
How to use the washing machine tap correctly
Some people like to tighten the water tap every time they use water, thinking that this will prevent water leakage. In fact, proper use of taps should be as light as possible. Do not vigorously rotate the faucet knobs. Do not rotate the faucet too tightly. In addition, the faucet should try not to bump into hard objects. For the use of the bathtub faucet, the showerhead metal hose should be kept in a natural stretch. When not in use, do not wrap it around the faucet. When using or not using it, pay attention to the joint between the hose and the valve body so that no dead angle is formed to avoid breakage or damage. hose.
The above about the automatic washing machine faucet leak how to do and solutions to a simple introduction to here, I hope to help you. For more information, please visit this website. Stay tuned.
Washing machine faucet
Hand Pallet,Manual Pallet Jack,Hand Pallet Jack,Hydraulic Pallet Truck
Guangdong Gongyou Lift Slings Machinery CO.,LTD , https://www.workmatehoist.com