The restroom is the third major focus of our renovation of the house. There are many pipes in the bathroom, and there are many circuits. Pay attention to waterproofing during the decoration. The renovation of the restroom is about the kind of peace of mind that comes into normal operation and the safety of people when they use it. So what should I do to waterproof the bathroom? Then let Xiaobian take everyone to see the relevant content of the waterproof content of the bathroom .
First, the toilet waterproof process
1. Brush the first time waterproof coating. Ensure that the construction site is clean and dry before construction, and the waterproof coating should be covered without any omission. It is firmly bonded to the base layer, free from cracks, no bubbles, and no falling off. The brushing height is consistent and the thickness is required to meet the product requirements.
2. Brush the second time waterproof coating. Note that there is a certain time interval between the first and second passes of the waterproof coating. The second pass can be carried out after the first pass of the paint is dry, depending on the coating. The interval is too short and the waterproof effect will be greatly reduced.
3. Spread the protective layer. In order to prevent the subsequent construction from damaging the waterproof layer, it is necessary to apply a protective layer on the surface of the waterproof coating. The protective layer should completely cover the waterproof layer, and there is no leakage. It is firmly bonded to the base layer, free from cracks, no bubbles, and no falling off.
4. Closed water test. In the closed water test, the water at the highest point on the ground shall not be less than 2 cm, and it shall be stored for at least 24 hours, and it shall be qualified after observing no leakage. If there is leakage, you need to redo it, and you should not neglect it.
Base treatment, cleaning, screed layer, joint layer, detail additional layer, acrylic waterproof layer, water storage test, protective layer construction, secondary water storage test.
The elevation of the kitchen and bathroom should be checked correctly, paying special attention to the correct position of the floor drain.
Second, the bathroom waterproof details
1. Make sure the floor of the bathroom is relatively stable. If you need to replace the floor tiles of the bathroom, after you have cut the original floor tiles, you must first level the floor with cement mortar and then do waterproofing. This can prevent leakage of the waterproof coating due to uneven thickness.
2. The seam should be painted in place. The seam between the bathroom wall and the joint between the upper and lower water pipes and the ground is the most prone to problems.
3. Wall treatment is also very important. In the general bathroom waterproofing treatment, the wall surface should also be made of waterproof coating of about 30 cm high to prevent water from oozing through the wall. However, if the wall of the bathroom is a non-load-bearing light-weight wall, the entire wall should be covered with waterproof coating.
4, waterproof test must be done. After the construction of the bathroom is completed, all the water in the bathroom will be blocked, and a 25 cm high "can" will be built at the door, and then 20 cm of water will be poured into the bathroom.
5, keep the water flowing smoothly. All sewer pipes in the bathroom, including floor drains, plumbing pipes for sanitary ware, etc., should be kept open.
How about, I read the above-mentioned introduction to the waterproof of the bathroom, and I also learned a lot about the waterproof content of the bathroom. I hope that you can learn more about home improvement knowledge through this article, and you will be able to create a more perfect home environment. Thank you for reading this article and your support and love for Xiaobian. If you want to get more information about home improvement, please continue to pay attention to the decoration home network.
The folding pole for streetlights is a new and innovative solution for urban lighting. It is designed to provide a convenient and practical way to install and maintain streetlights in tight spaces. The folding pole is made of high-quality materials and is engineered to withstand harsh weather conditions and heavy use.
The pole can be easily folded and stored when not in use, making it an ideal solution for temporary lighting applications. It can also be used in areas where traditional poles are not feasible due to space constraints or other limitations.
The folding pole is easy to install and can be quickly set up by a single person. It can be adjusted to different heights and angles, allowing for customized lighting solutions that meet the specific needs of any project.
Overall, the folding pole for streetlights is a versatile and practical solution that offers a range of benefits to urban planners, lighting designers, and maintenance crews.
Street Light Flexible Pole,Outdoor Light Pole,Steel Pole,Adjustable Pole,Hinged Pole,Octagon Pole
Yangzhou M.T. New Energy & Lighting Group Co., Ltd. , https://www.mtstreetlight.com