Everyone knows that the current housing prices have experienced a lot of damage. As a result, many people have no choice but to use second-hand housing. They must be aware that second-hand houses are old homes after all. Following small to tell you about the need to pay attention to what the refurbishment and renovation of these points need to acquire knowledge in advance.
1, for the toilet closed water test
Before refurbishment, one of the first things to do is close the water test on the bathroom, be sure to check that the previous waterproofing is done well. The method of operation is relatively simple, the method is: block the floor drain, and then put 5CM water in the toilet, observation time to reach 24 hours before going to the next time to go downstairs neighbors home inspection, if there is no leakage phenomenon, then you can see This bathroom is well-waterproofed. If there is a leak, then it must be re-done. Remember that after the waterproof treatment is completed, the later construction must wait for the ground to dry completely and the ground cracking will not occur.
2, water, circuit transformation processing
Water and circuit transformation can be said to be the most complicated ones in the transformation of old houses. Waterway reconstruction, the majority of people use the water pipe is used 50 years of quality assurance of the tube. After all the waterway transformation is complete, it must be tested for it so that it can be checked out where it will not leak, if there is an emergency treatment. The transformation of the circuit, the general use of the previous house is more aluminum wire, then re-reform it must be removed before it, a lot of modern home appliances, for safety reasons the family is best to use 2.5 mm copper wire is better, For a line of high-power electrical appliances such as air conditioners, it is necessary to use a 4-mm square line. Also keep in mind that PVC insulation must be used when embedding in the wall.
3, stucco wall, base is the key
The long time that lived in the wall of the old house is the phenomenon of cracking and peeling. In fact, the reason for this phenomenon is very simple, because when the wall was renovated, the grassroots did not handle it well. Now people's decoration is after the leveling on the wall, and then it will be coated with an interface agent, this can play a role in moisture, and it also has a function that can protect the role of latex paint, then do The step is to putty, putty paste to use waterproof putty, it must be remembered putty must scrape three times the effect will be better, and finally brush latex paint.
4, replace aluminum or steel doors and windows
If the old house still uses the previous wooden doors and windows, then you can check if there is no deformation or cracking phenomenon. If you do not indicate that the material is very good, you can change the decoration, do not need to be replaced, as long as it is affixed with a decorative plate, and then painted Paint it, so the effect is just as good. If it is iron doors and windows, the paint on its surface has fallen off. At this time, it is recommended that you replace it. You can replace it with aluminum or plastic steel.
Summary: on the renovation and decoration needs to pay attention to what and these decoration knowledge to grasp the relevant content in advance to introduce this, for the refurbishment decoration should pay attention to the details are still more, after all, this is the old house, if not dealt with later will bring great Trouble. I hope that the above introduction will help everyone.
High Temperature Alloy is divided into three kinds of material: 760 ℃ high-temperature material, 1200℃ high temperature and 1500 ℃ high temperature materials, the tensile strength is 800 mpa. On other words,it refers to the metal material worked well in the condition of 760-1500 ℃ or above. It owns excellent high temperature strength, good resistance to oxidation and thermal corrosion resistance, good fatigue properties, fracture toughness and other comprehensive performance, this kind of material has became an irreplaceable key material in military and civilian gas turbine engine hot end components . According to the relevant theory, 760 ℃ high-temperature materials, according to the matrix elements,can be mainly divided into high temperature iron base alloy, nickel base superalloy and cobalt-based super alloy. According to the preparation process,it can be divided into deformation and high temperature alloy, casting high temperature alloy and powder metallurgy super alloy. According to the solid methods,it can be divided into solid solution strengthening, precipitation strengthening and oxide dispersion strengthened with fiber reinforced type, etc.
High Temperature Alloy
High Temperature Alloy,High Temperature Alloy Wire,High Temperature Alloy Anti-Corrosion ,High Temperature Tooling Tungsten Alloy
Jiangsu nickel alloy Co.,Ltd , https://www.xhalloy.com