| Home>Bearing knowledge>Cooperation and skill requirements for high speed bearings |
High-speed bearing cooperation and skill requirements
| /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089'; |
(1) Scale changes and hardness changes from normal temperature to high temperature,
(2) Force changes and shape changes caused by centrifugal force at high speed.
In the high-speed, high-temperature conditions; from the cooperation and clearance selection to strive to adhere to the bearing precision and work function; this is difficult.
In order to ensure the deformation of the raceway behind the bearing device, the tomb is ridiculously ridiculously 螅 螅 螅 螅 螅 螅 螅 螅 螅 螅 螅 螅 螅 螅 螅 蛘 蛘 蛘 蛘 蛘 蛘 蛘The cooperation is lax; therefore, the excess is necessary to be carefully accounted for on the premise of thinking about the above two factors; the useful interference at normal temperature and normal speed may be invalid for high-speed bearings.
If the result of the calculation is too large (usually as long as it is under ultra-high speed); as long as the two-layer smooth method of the under-smooth smoothing method and the static-pressure smoothing method is adopted; and such a plan may make the dmn value of the bearing Break the 3 million mark.
In thinking about the high-speed bearing clearance, not only must consider the above factors; but also consider the influence of the thermal elongation of the shaft on the clearance; the bearing needs to be in the working condition; that is, the optimal clearance at the working temperature; The kind of play is formed in the state of accurate alignment between the inner and outer ring grooves. Because the high-speed bearing strives to reduce relative sliding and internal conflict; the best way is to adjust the relative misalignment of the inner and outer rings along the axial direction. The clearance of the ball bearing.
When thinking about the cooperative interference and clearance of the bearing; pay attention to the characteristics that the data becomes soft and simple deformation at high temperature; and the temperature change from normal temperature to high temperature repeatedly leads to the possibility of permanent eternal deformation.
2. Demand for mainframe-related parts High-speed bearing requirements Bearing reversal system through fine dynamic balance; shaft and seat hole bearing parts should have higher than the usual requirements of dimensional accuracy and shape accuracy; especially coaxiality and shoulder Straightness of the seat hole or journal; and when considering these difficulties; it is necessary to pay attention to the high-speed and high-temperature elements of the bearing work.
The shaft support system requires both high rigidity and the required quality as light as possible; in order to overcome this opposition; it can adopt methods such as reducing the appearance roughness and improving the appearance reinforcement to improve the support stiffness; using hollow shafts to reduce the system quality.
Recommend to friends comments close window
| Bearing related knowledge |
| Common terms and definitions for rolling bearing parts (1) The effect of bearing grease filling on bearing application FAG's optimization of reloading bearings and fine parts. Smoothness of rolling mill bearings. Classification of brick oil bearings and attention to matters |
This article links to http://
Please indicate the bearing network http://
Previous:The layout and sealing principle of the skeleton oil seal Next:The precautions for the bearing and pump shaft bearing housing
320W Quantum Board grow lights is a highly efficient plant growth lamp that uses advanced quantum plate technology. With a power of 320 watts, it provides enough light energy for plants to grow. Quantum plate technology can better simulate the natural spectrum and provide different wavelengths of light required by plants, thus promoting plant growth and development.
This led grow lights uses high quality LED lamp beads with long life, high brightness and low energy consumption. Its light is evenly distributed and can cover large planting areas. The lamps are also equipped with an efficient cooling system to ensure the stable operation and long-term use of the lamps.
The 320W Plant Light Quantum Board grow lights also features adjustable brightness and spectral functions. Users can adjust the brightness and spectrum of the lamps according to the needs of plant growth at different stages to promote the growth of plants to the greatest extent. The lamp also has a timing switch function, which is convenient for users to control the lighting.
In short, 320W Plant Light Quantum Board led grow lights is an efficient, adjustable plant growth lamp, suitable for indoor planting, greenhouse planting and other plant growth environment. It can provide sufficient light energy, promote the growth and development of plants, and is an ideal choice for plant growers
controller led full spectrum grow light 320W,best quantum board led grow lights,quantum board samsung lm301h 320w
Shenzhen Pvison Technology Co., Ltd. , https://www.pvisunggrowlight.com